What I’m reading is that these leaders are alarmed about the fairness of an investigation meanwhile they have thousands of these masked goons running around their streets unchecked which should be the real source of alarm.

Its been super mild here in the PNW this winter. Not a lot of rain outside of some specific instances a few weeks ago which lead to flooding and the temps have only dipped into the 30’s a few times.

I was actually just looking at this last night and I think the best two options are melting into silicon molds and embedding into resin in silicon molds. Uncle Jessy has a good tutorial on YouTube of both the former and latter.

They dont give a fuck about the average citizen. These are the same people that voted to slash funding Medicaid just a couple months ago. These are the same people that voted against impeaching Trump a couple months before that. These people want Republicans to pass every shithole bill they can because it’s better for their bank account in the long run and the typical rube will blame the Republicans for it happening.

Yes you can and it happens all the time. A getaway driver in a bank robbery gets charged just the same as the guys shooting people inside the bank.

Great, then you should be satisfied with the state of the country and have nothing to complain about.

You’re absolutely right but the previous president decided to wait four years to even charge him, after he’d already won the '24 Republican nomination, in order to pretend like he was taking action without risking actual consequences for Trump that might prevent him from winning the election for them.

Yeah thats just a seal to keep the poop in but not what holds it down to the floor (mostly).

I’ve never seen support material visually improve overhangs apart from the specialized support filament that doesn’t bond with the print material. Traditional support always leaves a gap between the support material and the print material, otherwise they’d fuse together and become one with the print, meaning even with support, the print material sags anyway.

OP would probably be better served with adaptive layers and using a much finer layer height in the overhang region.

Bill is late paying his rent so Hank is giving him alternative options.

https://www.reddit.com/r/howto/comments/163r412/how_to_get_proof_of_residency_at_an_old_address_i/

This person was in the same exact boat and was able to get proof of their old residency from their credit report

If we entertain their argument we could also claim that if she’d been given that $3M earlier, she wouldn’t have had that person as her landlord and they’d still be alive therefore these people share responsibility for the landlord’s death.

There’s also the possibility they’re referring to the current draw through the mobo connector itself frying things. A couple of HDDs at 12V, 10W will be pulling almost 2A which can be a lot for some circuit board traces, but there’s no great way know what the board can handle without documentation from the manufacturer or someone with relevantt engineering experience well above what a typical computer repair shop would have.

If I were OP I would just roll the dice and try it out. Its not as if old Dell office PCs are high dollar items.

I literally never once uttered those words but go ahead and keep deflecting from the real issues.

You appear to share the same magical thinking, faith-based belief system as someone who donates money to televangelists thinking that will make god will fix their problems for them despite all evidence pointing to the contrary. “It hasnt worked the last one hundred times I’ve done it but surely this time will be different. How dare you suggest I try literally anything else. That’s the devil talking!”

I see what you mean now.

Even still, our toilets in the US are bolted to the floor and only sealed with caulking along the floor to keep water from pooling underneath and rotting the floor. With our American diets, we rely on the structural rigidity of metal bolts to keep things in place during our massive dumps

Those are the molex to sata power adapters that are a fire hazard. I haven’t ever heard of this type causing issues and have been using them for years and years without issue.

Toilet seat got glued in as well.

I’ve gotta see a picture of this too. I’ve never seen a toilet seat that wasn’t bolted to the toilet.

Do you guys even think twice about the things you like getting angry about??

I guarantee if they went the other way and only offered a stripped down dashboard with little configurability people would also be complaining that they can’t customize things to best suit their needs.

On a new install specifically when you select the option to auto-generate a dashboard during setup.

To hide sidebar items in a browser you can click on the top left “Home Assistant” button or click on your username at the bottom left and select “Change the order and hide items from the sidebar” in User Settings.

Oh okay “politicians are goals that people kick their ball into” therefore it’s okay for Democrats to enable the Republican agenda at every turn. Thanks for clarifying things.